View APA7063KI-TU_1210671.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

APA7063
Stereo 1.5W Audio Power Amplifier with DC Volume Control
Features
* * * * * * * * * * * * * Operating Voltage: 3.3V to 5V DC Volume Control Interface, 0dB to -105dB Depop Circuitry Integrated Thermal shutdown protection circuitry High supply voltage ripple rejection Low Supply Current, IDD = 13mA at Stereo BTL Low Shutdown Current, IDD = 0.7A Bridge-Tied Load (BTL) or Single-Ended-(SE) Modes Operation Output Power at 1% THD+N, VDD=5V -1.2 W/Ch (typ) into an 8 Load Output Power at 10% THD+N, VDD=5V -1.5 W/Ch (typ) into an 8 Load Low Crossover Distortion Low Quiescent Current Bridge-tied or Stereo(Single-ended) Configurations
General Description
The APA7063 is a monolithic integrated circuit that provides DC volume control, and a stereo bridged audio power amplifiers capable of producing 1.5W(1.2W) into 8 with less than 10%(1.0%) THD+N. APA7063 provides a volume control pin DC_Vol determines the attenuation of output of the amplifiers. The attenuator range is from 0dB (DC_Vol=0.7VDD) to -105dB (DC_Vol=0V) with 32 steps. Both of the depop circuitry and the thermal shutdown protection circuitry are integrated in the APA7063, that reduces pops and clicks noise during power up and when using the shutdown modes and protects the chip from being destroyed by over temperature failure. To simplify the audio system design applications, the APA7063 combines a stereo bridge-tied loads (BTL) mode for speaker drive and a stereo single-end (SE) mode for headphone drive into a single chip, where both modes are easily switched by the SE/BTL input control pin signal. The APA7063 also features a shutdown function which keeps the supply current only 0.7A (typ).
Applications
* Portable and Desktop Computers * Multimedia Monitors * Portable Radios, PDAs, and Portable TVs
Pin Description
SHUTDOWN VCC DC Vol Vo1 Vin1 Vin2 Vo2 GND 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 + OUT1 VCC - OUT1 Bypass SE/BTL - OUT2 VCC + OUT2
ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 1 www.anpec.com.tw
APA7063
Ordering and Marking Information
APA7063
H a n d lin g C o d e Tem p. Range P ackag e C ode Package Code J : P D IP - 1 6 Tem p. Range I : - 4 0 to 8 5 C H a n d lin g C o d e TU : Tube
K : SO P - 16
TR : Tape & Reel
APA7063 J :
APA7063 XXXXX
X X X X X - D a te C o d e
APA7063 K :
APA7063 XXXXX
X X X X X - D a te C o d e
Block Diagram
SE/BTL 10K 10K
Vo1
Vin1
Bias Vin2 +
Volume Control 32 steps
Vo2 Shutdown VCC GND Bypass Power Management Click and Pop Suppression Circuitry 20K + + - OUT2
10K
10K
Absolute Maximum Ratings
(Over operating free-air temperature range unless otherwise noted.)
Symbol VDD TA TJ TSTG TS VESD Parameter Supply Voltage Operating Ambient Temperature Range Maximum Junction Temperature Storage Temperature Range Soldering Temperature,10 seconds Electrostatic Discharge
2
Rating 6 -40 to 85 150 -65 to +150 260 -2000 to 2000*1
Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003
+ -
+ 20K 20K + 20K
+ OUT1
- OUT1
+ OUT2
Unit V C C C C V
www.anpec.com.tw
APA7063
Electical Characteristics
Electrical Characteristics for Entire IC
The following specifications apply for VDD= 5V unless otherwise noted. Limits apply for TA= 25C
Symbol VDD IDD ISD VIH VIL
Parameter Supply Voltage Quiescent Power Supply Current Shutdown Current SE/BTL High Input Voltage SE/BTL Low Input Voltage
Test Conditions Min. 3.3 VIN=0V, IO =0A VPIN 2= VDD 4
APA7063 Typ. Max. 5.5 13 25 0.7 2.0 0.8
Unit V mA A V V
Electrical Characteristics for Volume Attenuators
The following specifications apply for VDD= 5V. Limits apply for TA= 25C
Symbol CRANGE
Parameter Attenuator Range
Test Conditions Gain with VpIN 3=5V Attenuation with VpIN 3=0V
APA7063 Min. Typ. Max. 0.5 -100 -105
Unit dB
Electrical Characteristics for BTL Mode Operation
The following specifications apply for VDD= 5V unless otherwise noted. Limits apply for TA= 25C
Symbol VOS PO
Parameter Output Offset Voltage Output Power
Test Conditions
THD+N
VIN=0V THD=1%, f=1kHz RL=8 THD=10%, f=1kHz RL=8 Total Harmonic Distortion + Noise AVD =2, 20HzAPA7063 Typ. 5 1.2 1.5 0.3 1.0 74 95 40
Unit mV W
% dB dB uV
RSRR XTALK VN
Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003
3
www.anpec.com.tw
APA7063
Electical Characteristics (Cont.)
Electrical Characteristics for SE Mode Operation
The following specifications apply for VDD= 5V unless otherwise noted. Limits apply for TA= 25C
Symbol VDS PO
Parameter Output Offset Voltage Output Power
Test Conditions
VIN=0V, THD=1%, f=1KHZ, RL=32K THD=10%, f=1KHZ, RL=32K THD+N Total Harmonic Distortion plus AV= 1,VOUT=1 VRMS, f=1KHZ, RL=1K Noise PO= 75mW, RL=32K, Av=1, f=1KHZ RSRR Power Supply Rejection Ratio VRIPPLE= 200mVRMS, f=120Hz,CB=2.2F XTALK Channel Separation f=1KHZ, CB=2.2F VN Output Noise Voltage RL=1K, A-Wtd Filter
APA7063 Typ. 100 95 100 0.01 0.05 58 95 30
Unit mV mW dB dB uV
Pin Description
Pin Name Shutdown VDD DC_Vol Vo1 Vin1 Vin2 Vo2 GND +OUT2 -OUT2 SE/BTL Bypass -OUT2 +OUT1 No 1 2,10,15 3 4 5 6 7 8 9 11 12 13 14 16 I/O 1 Description Shutdown mode control signal input, place entire IC in shutdown mode when held high, Idd=0.7uA. Supply voltage input pin. Volume control function input pin. Channel 1 output for external feedback circuit. Audio input channel 1 Audio input channel 2 Channel 2 output for external feedback circuit. Ground connection for circuitry. Channel 2 positive output in BTL mode and high impedance state in SE mode. Channel 2 negative output in BTL mode and in SE mode. Mode control signal input, hold low for BTL mode, hold high for SE mode. Connect to voltage divider for internal mid_supply bias Channel 1 negative output in BTL mode and in SE mode. Channel 1 positive output in BTL mode and high impedance state in SE mode.
I O I I O
O O I I O O
Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003
4
www.anpec.com.tw
APA7063
Typical Application Circuit
#8
1F R_var
220F Shutdown +OUT1 VCC -OUT1 Vbypass SE/BTL -OUT2 VCC +OUT2 L-ch 100k R-ch 100k
#8
1k
r*=R_var/50
VCC 20k DC_Vol Vo1 Vi1 Vi2 Vo2 20k GND
R-in L-in
1F
20k 20k
1F
APA7063
220F
Headphone jack
1k
* Add a resistor to avoid volume control gain error at power on status. For the R_var with 10K variable resistor, the recommended value of r is in range of 100~200.
Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003
5
www.anpec.com.tw
APA7063
Typical Characteristics
THD+N-Total Harmonic Distortion+Noise (%)
10 5 2 1 0.5 0.2 0.1 0.05 0.02 0.01 20
VDD=5V RL=8 Po=1.0W BTL
THD+N-Total Harmonic Distortion+Noise (%)
5
2 1 0.5 0.2 0.1 0.05
VDD=5V RL=16 Po=0.5W BTL
AV=8
AV=2
AV=4
AV=2
AV=4
0.02 0.01 20
AV=8
50
100
200
500
1k
2k
5k
10k 20k
50
100
200
500
1k
2k
5k
10k 20k
Frequency (Hz)
Frequency (Hz)
THD+N-Total Harmonic Distortion+Noise (%)
10 5 2 1 0.5 0.2 0.1 0.05
THD+N-Total Harmonic Distortion+Noise (%)
10 5 2 1 0.5
VDD=5V RL=8 BTL
VDD=5V RL=16 BTL
f=20kHz
f=20kHz
0.2 0.1 0.05 0.02 0.01 10m
f=1kHz f=20Hz
f=1kHz f=20Hz
0.02 0.01 10m
20m
50m
100m
200m
500m
1
2
20m
50m
100m
200m
500m
1
Output Power (W)
Output Power (W)
Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003
6
www.anpec.com.tw
APA7063
Typical Characteristics (Cont.)
THD+N-Total Harmonic Distortion+Noise (%)
10 5 2 1 0.5 0.2
THD+N-Total Harmonic Distortion+Noise (%)
10 5 2 1 0.5
VDD=5V RL=8 Po=0.25W SE
VDD=5V RL=32 Po=75mW SE
AV=1
0.1 0.05 0.02 0.01 0.005 0.002 0.001 20 50 100 200 500 1k 2k 5k 10k 20k
AV=1
0.1 0.05 0.02 0.01 20
AV=4 AV=2
AV=4 AV=2
50 100 200 500 1k 2k 5k 10k 20k
Frequency (Hz)
Frequency (Hz)
THD+N-Total Harmonic Distortion+Noise (%)
THD+N-Total Harmonic Distortion+Noise (%)
10 5 2 1 0.5
10 5 2 1 0.5 0.2 0.1 0.05 0.02 0.01 10m
VDD=5V RL=10k Vin=1Vrms SE
VDD=5V RL=8 SE
f=20kHz f=20Hz f=1kHz
0.1 0.05 0.02 0.01 0.005
AV=1
AV=4 AV=2
0.002 0.001 20 50 100 200 500 1k 2k 5k 10k 20k
20m 30m
50m 70m
200m
500m
Froquency (Hz)
Output Power (W)
Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003
7
www.anpec.com.tw
APA7063
Typical Characteristics (Cont.)
THD+N-Total Harmonic Distortion+Noise (%)
10 5 2 1 0.5
THD+N-Total Harmonic Distortion+Noise (%)
VDD=5V RL=32 SE
10 5 2 1 0.5
VDD=5V RL=10k SE
0.1 0.05 0.02 0.01 0.005 0.002 0.001 10m 20m
f=20kHz f=20Hz
0.1 0.05 0.02 0.01 0.005
f=20kHz
f=1kHz
f=1kHz
0.002 0.001 100m 200m 300m 500m 800m 1
f=20Hz
30m
50m 70m 100m
200m
2
3
Output Power (W))
Output Voltage (V)
THD+N-Total Harmonic Distortion+Noise (%)
10 5 2 1 0.5 0.2 0.1 0.05 0.02 0.01 20
THD+N-Total Harmonic Distortion+Noise (%)
10 5 2 1 0.5 0.2 0.1 0.05 0.02 0.01 20
VDD=3.3V RL=8 Po=0.4W BTL
VDD=3.3V RL=16 Po=0.2W BTL
AV=2
AV=8
AV=2
AV=8
AV=4
50
100
200
500
1k
2k
5k
10k 20k
50
100
200
500
1k
2k
5k
10k 20k
Frequency (Hz)
Output Power (W)
Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003
8
www.anpec.com.tw
APA7063
Typical Characteristics (Cont.)
THD+N-Total Harmonic Distortion+Noise (%)
THD+N-Total Harmonic Distortion+Noise (%)
10 5 2 1 0.5 0.2 0.1 0.05
10 5 2 1 0.5 0.2 0.1 0.05
VDD=3.3V RL=8 BTL
VDD=3.3V RL=16 BTL
f=20kHz
f=20kHz
f=1kHz f=20Hz
f=1kHz f=20Hz
0.02 0.01 10m
0.02 0.01 10m
20m 30m
50m 80m
200m
400m
800m
20m 30m
50m 70m
200m
500m
Output Power (W)
Output Power (W)
THD+N-Total Harmonic Distortion+Noise (%)
10 5 2 1 0.5 0.2 0.1 0.05 0.02 0.01 20
THD+N-Total Harmonic Distortion+Noise (%)
10 5 2 1 0.5 0.2 0.1 0.05 0.02 0.01 20
VDD=3.3V RL=8 Po=100mW SE
VDD=3.3V RL=32 Po=35mW SE
AV=1 AV=4 AV=2
50 100 200 500 1k 2k 5k 10k 20k
AV=1 AV=4 AV=2
50 100 200 500 1k 2k 5k 10k 20k
Frequency (Hz)
Frequency (Hz)
Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003
9
www.anpec.com.tw
APA7063
Typical Characteristics (Cont.)
THD+N-Total Harmonic Distortion+Noise (%)
10 5 2 1 0.5 0.2 0.1 0.05
THD+N-Total Harmonic Distortion+Noise (%)
10 5 2 1 0.5 0.2 0.1 0.05
VDD=3.3V RL=10k Vin=1Vp SE
VDD=3.3V RL=8 SE
f=20kHz
f=20Hz
AV=1 AV=2
f=1kHz
0.02 0.01 10m
0.02
AV=4
0.01 20 50 100 200 500 1k 2k 5k 10k 20k
20m
30m
50m
70m 100m
200m
Frequency (Hz)
Output Power (W)
THD+N-Total Harmonic Distortion+Noise (%)
10 5 2 1 0.5 0.2 0.1 0.05
THD+N-Total Harmonic Distortion+Noise (%)
10 5 2 1 0.5 0.2 0.1 0.05
VDD=3.3V RL=32 SE
VDD=3.3V RL=10k SE
f=20kHz
f=1kHz f=20kHz
f=1kHz
0.02
0.02
f=20Hz
0.01 10m 12m 15m 20m 25m 30m 35m 42m 55m
f=20Hz
0.01 100m 200m 300m 500m 700m 1 2
Output Power (W)
Output Voltage (V)
Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003
10
www.anpec.com.tw
APA7063
Typical Characteristics (Cont.)
THD+N-Total Harmonic Distortion+Noise (%)
10 5 2 1 0.5
THD+N-Total Harmonic Distortion+Noise (%)
10 5 2 1 0.5 0.2 0.1 0.05 0.02
VDD=5V RL=10k docking
VDD=3.3V RL=10k docking
0.1 0.05 0.02 0.01 0.005 0.002 0.001 100m 200m 300m
f=20kHz
f=20kHz
f=1kHz f=20Hz
f=1kHz f=20Hz
200m 300m 500m 700m 1 2
0.006 100m
500m
800m 1
2
3
Output Voltage (V)
Output Voltage (V)
100u
100u
No filter
VN-Output Noise Voltage( V)
50u
No filter A_wtd filter
VN-Output Noise Voltage( V)
50u
A_wtd filter
20u
20u
10u
10u
5u
5u
2u
VDD=5V RL=8 Av=2V/V BTL
50 100 200 500 1k 2k 5k 10k 20k
2u
VDD=5V RL=10k Av=1V/V SE
50 100 200 500 1k 2k 5k 10k 20k
1u 20
1u 20
Frequency (Hz)
Frequency (Hz)
Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003
11
www.anpec.com.tw
APA7063
Typical Characteristics (Cont.)
+0
+0
-20
Crosstalk (dB)
-40
Crosstalk (dB)
VDD=5V RL=8 Po=1W Av=2V/V BTL
-20
-40
VDD=5V RL=32 Po=75mW Av=1V/V SE
-60
-60
-80
f=1kHz
-80
f=1kHz
-100
-100
f=20kHz f=20kHz
-120 20 50 100 200 500 1k 2k 5k 10k 20k -120 20 50 100 200 500 1k 2k 5k 10k 20k
Frequency (Hz)
Frequency (Hz)
+12
0.7 0.6 0.5 0.4
RL=8
+10
+8
Cf=0.1F Cf=0.068F
+6
PD-Power Disspation (W)
Cf=0.22F
Gain (dBV)
RL=16
0.3 0.2 0.1 0
+4
+2
VDD=5V RL=8 Av=2V/V BTL
50 100 200 500 1k 2k 5k 10k 20k
RL=32 VDD=5V THD<1% BTL
0 0.25 0.5 0.75 1 1.25 1.5
-0 20
Frequency (Hz)
Output Power (W)
Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003
12
www.anpec.com.tw
APA7063
Typical Characteristics (Cont.)
0.2 0.18
20
No Load
PD-Power Disspation (W)
0.16 0.14 0.12 0.1 0.08 0.06 0.04 0.02 0 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4
IDD-Supply Current (mA)
RL=8
1 7.5 15 1 2.5 10 7 .5 5 2 .5 0 1 1 .5 2 2 .5 3 3 .5 4 4 .5 5 5 .5
BTL
RL=16
RL=32 VDD=5V THD<1% SE
SE
Output Power (W)
VDD-Supply Voltage (V)
2 1.8 1.6
VDD=5V RL=8 BTL
0.16 0.14
VDD=5V RL=32 SE
Output Power (W)
1.4 1.2 1 0.8 0.6 0.4 0.2 0 2.5 3 3.5 4 4.5 5 5.5
Output Power (W)
0.12 0.1 0.08
THD=10% THD=1%
THD=10%
0.06 0.04 0.02 0 2.5 3 3.5 4 4.5 5 5.5
THD=1%
VDD-Supply Voltage (V)
VDD-Supply Voltage (V)
Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003
13
www.anpec.com.tw
APA7063
Typical Characteristics (Cont.)
3
0.8
2.5
VDD=5V BTL
0.7
VDD=5V SE
Output Power (W)
2
Output Power (W)
0.6 0.5 0.4 0.3 0.2 0.1 0
1.5
1
0.5
THD=10% THD=1%
THD=10% THD=1%
0 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64
4
8 12 16 20 24 28 32 36 40 44 48 52 56 60 64
Load Resistance ()
Load Resistance ()
1.1 1 0.9
VDD=3.3V BTL
0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64
THD=10% THD=1%
Output Power (W)
0.8
0.34 0.32 0.3 0.28 0.26 0.24 0.22 0.2 0.18 0.16 0.14 0.12 0.1 0.08 0.06 0.04 0.02 0 4
VDD=3.3V SE
Output Power (W)
THD=10% THD=1%
8 12 16 20 24 28 32 36 40 44 48 52 56 60 64
Load Resistance ()
Load Resistance ()
Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003
14
www.anpec.com.tw
APA7063
Typical Characteristics (Cont.)
20 0 -2 0
+0
VDD=5V SE
-10 -20
PRSS (dBgA)
Gsin (dBV)
VDD=5V Vin=200mVp RL=8 Cb=2.2F SE/BTL
-30 -40 -50 -60
-4 0 -6 0 -8 0 -1 00 -1 20 0 .0 0 .5 1 .0 1 .5 2 .0 2 .5 3 .0 3 .5 4 .0 4 .5 5 .0
-70 -80 20
50
100
200
500
1k
2k
5k
20k
Voltage (V)
Frequency (Hz)
Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003
15
www.anpec.com.tw
APA7063
Packaging Information
SO - 300mil ( Reference JEDEC Registration MS-013)
D N
H
E
GAUGE PLANE
123 A e B A1 L
1
Millimeters Dim A A1 B D E e H L N 1 Min. 2.35 0.10 0.33 Max. 2.65 0.30 0.51
Variations- D Variations SO-16 SO-18 SO-20 SO-24 SO-28 SO-14 Min. 10.10 11.35 12.60 15.20 17.70 8.80 Max. 10.50 11.76 13 15.60 18.11 9.20 Dim A A1 B D E e H L N 1
Inches Min. 0.093 0.004 0.013 Max. 0.1043 0.0120 0.020
Variations- D Variations SO-16 SO-18 SO-20 SO-24 SO-28 SO-14 Min. 0.398 0.447 0.496 0.599 0.697 0.347 Max. 0.413 0.463 0.512 0.614 0.713 0.362
See variations 7.40 7.60
See variations 0.2914 0.2992
1.27BSC 10 0.40 10.65 1.27
0.050BSC 0.394 0.016 0.419 0.050
See variations 0 8
See variations 0 8
Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003
16
www.anpec.com.tw
APA7063
Packaging Information (Cont.)
PDIP-16 pin ( Reference JEDEC Registration MS-001)
D
E1
E
A2
A3
Dim A A1 A2 A3 D E E1 L eB
Millimeters Min. 0.380 3.169 2.915 18.632 7.605BSC 6.210 0 8.492 6.464 380.25 9.506 0.245 0 0.335 Max. 5.320 3.422 3.803 19.646 Min. 0.015 0.125 0.115 0.735
A1
A
Inches Max. 0.210 0.135 0.150 0.775 0.300BSC 0.255 15 0.375
Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003
17
www.anpec.com.tw
eB
L
APA7063
Physical Specifications
Terminal Material Lead Solderability Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb) Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3.
Reflow Condition
(IR/Convection or VPR Reflow)
Reference JEDEC Standard J-STD-020A APRIL 1999
temperature
Peak temperature
183C Pre-heat temperature
Time
Classification Reflow Profiles
Convection or IR/ Convection Average ramp-up rate(183C to Peak) 3C/second max. 120 seconds max Preheat temperature 125 25C) 60 - 150 seconds Temperature maintained above 183C Time within 5C of actual peak temperature 10 -20 seconds Peak temperature range 220 +5/-0C or 235 +5/-0C Ramp-down rate 6 C /second max. 6 minutes max. Time 25C to peak temperature VPR 10 C /second max.
60 seconds 215-219C or 235 +5/-0C 10 C /second max.
Package Reflow Conditions
pkg. thickness 2.5mm and all bgas Convection 220 +5/-0 C VPR 215-219 C IR/Convection 220 +5/-0 C pkg. thickness < 2.5mm and pkg. volume 350 mm pkg. thickness < 2.5mm and pkg. volume < 350mm Convection 235 +5/-0 C VPR 235 +5/-0 C IR/Convection 235 +5/-0 C
www.anpec.com.tw
Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003
18
APA7063
Reliability test Program
Test item SOLDERABILITY HOLT PCT TST ESD Latch-Up Method MIL-STD-883D-2003 MIL-STD-883D-1005.7 JESD-22-B, A102 MIL-STD-883D-1011.9 MIL-STD-883D-3015.7 JESD 78 Description 245 C , 5 SEC 1000 Hrs Bias @ 125 C 168 Hrs, 100 % RH , 121 C -65 C ~ 150 C , 200 Cycles VHBM > 2KV, VMM > 200V 10ms , Itr > 100mA
Carrier Tape & Reel Dimensions
t E Po P P1 D
F W
Bo
Ao
D1
Ko
T2
J C A B
T1
Application
A 330 1
B 62 +1.5 D
C 12.75+ 0.15 D1
J 2 0.5 Po 4.0 0.1
T1 12.4 0.2 P1 2.0 0.1
T2 2 0.2 Ao 6.4 0.1
W 12 0. 3 Bo 5.2 0. 1
P 8 0.1 Ko 2.1 0.1
E 1.750.1 t 0.30.013
SOP- 8
F 5.5 1
1.55 +0.1 1.55+ 0.25
Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003
19
www.anpec.com.tw
APA7063
Cover Tape Dimensions
Application SOP- 8 Carrier Width 12 Cover Tape Width 9.3 Devices Per Reel 2500
Customer Service
Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369
Copyright ANPEC Electronics Corp. Rev. A.5 - Mar., 2003
20
www.anpec.com.tw

▲Up To Search▲

Price & Availability of APA7063KI-TU

	To Download APA7063KI-TU Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .